Heavy Duty Close Chamber Abrasive Cut-Off Machine

Model : METACUT-50 (SACT) – table top model

	Cutting Capacity : 60/80/100 mm round bar. High Power suitable motor backup. Component hold in sturdy vice
	Specially designed wheel guard ensures effective coolant delivery thus burn-free cut.
	See through window. Door limit switch, internal illumination
	Effortless cutting with lever mechanism
	Standard control panel with door open, pump on / power on indications, emergency stop. Illumination on / off, safety, switches along with other optional electronic circuits available.

Open Type Abrasive Cut-Off Machine

Model : METACUT (WS – 50)

	Cutting capacity – 60 mm / 80 mm / 100 mm round / Square, high power suitable motor backup.
	Heavy duty vice, Coolant circulation system along with coolant
	Tank & Pump

Optional –
X-Y Sliding Base Plate for sample positioning & parallel cut, cutting small components.
   

Top

Specimen Mounting Press

Model : META – MOUNT,  Model : AUTO-MOUNT (Microprocessor based)

	Permanent Mounting of metallography specimen for  correct polishing results
	Helps polishing small specimens & edge retention
	Reliable hydraulic jack with pressure gauge
	Mould heater fast cooling (air/water), timer; buzzer facilities, automatic cycles
	Electronic auto auto off

Top

Belt Grinder  :
Model MBG-II,  & Model MBG-III (With 1 HP Motor) 

	For initial Rough Grinding
	Motor – ¼ HP, 220V, single phase
	Endless belt dim. – 100 x 915 mm
	Dynamically well balanced rollers
	Enclosed model with water faucet for intermediate rinsing of specimen for avoiding heating / burn formation

Top

Variable Speed Double Disc Grinding / Lapping Machine
Model “ METAPOL DC-II

	High torque, noise less operation
	D.C. Motor of ½ or 1 HP  (Single or dual motors) with D.C. Drive Continuous stepless variable speed upto 1400 r.p.m
	Quick Paper Clamping arrangement
	Tough F.R.P. anticorrosive top with sink & water faucet.Digital R.P.M. indicator
	Disc Dia. 200 mm (Optional 250 mm)

Top

Variable Speed Double Dis Grinding / Lapping Machine

Model : POLISHING STATION

	Complete metallography Polishing set up
	Double Disc variable speed, backed up by high torque, noiseless D.C. motors  of ½ HP, with D.C. Drives, driving discs independently.
	Disc dia – 200 mm
	Continuous stepless variable speed upto 1400 r.p.m. with Digital R.P.M. indicator

Top

Variable Speed Single Dis Grinding / Lapping Machine

Model : METAPOL DC-I

Specification – Same as  Model : Metapol DC-II
 

Top

Automatic Multi Specimen Grinder/Polisher - AUTOPOL–II 

Automatic grinder / polisher improves the productivity quality of preparation with much less operator dependence, offering completely scratch less specimen.

	Six specimen polished simultaneously
	Motor capacity – 1 HP DC, with DC drive
	Supply – 230 V, AC, Single Phase
	Disc 200 mm
	Polishing load – 150 PSI (Pneumatic)
	Supplied with sample leveling press.

Optional –
Specimen holder dis for embedded specimen of 32 mm, 38 mm & odd shape specimen.
Automatic Fluid Dispensing unit for water slurry with stirrer.
 

Top

Portable Grinder / Polisher Model : PORTGRINDER

	Variable speed, High torque
	Flexible shaft
	90º handle
	38 mm disc for PSA paper & cloths
	Supply 230 V. AC

Top

Automatic Electrolytic Polishing / Etching System

Model : ELECTROPOL 

Micro specimen prepared within 30 secs. Beneficial for good work Volume labs and for soft metals Minimal initial preparation.   Totally Operator independent process.  Pay back period just one and half Year. Micro  controller technology.
  

Top

Portable Auto Electro Polisher   - Model : PORTPOL

	Automatic digital electro polisher, Auto/Manual Modes, With timers, Electrolyte flow regulation
	38 mm disc for PSA paper & cloths
	Supply 230 V. AC
	Current – 2.5 Amp., Voltage – 80V, Supply – 230 V.A.C.Polishing probes – Unique Pen Type system with Recirculation of electrolyte, pump 25 watts reservoir (0.5 Ltr)
	Pre-grinding required is much less.

Top

Jominy End Quench Hardenability Set Up

Model - MT-JEQF
(as per SAE J406 May 85 and BS std 4437 – 1969)

	Special Furnace with DTC, Thyristor controlled panel avoids temp. over shooting
	At a time three Jominy test can be carried out.
	Quick transfer of specimen to quenching fixture within specific time time with the special tong
	Quenching Fixture designed strictly as per BS/SAE with specifications like 45º angle of top plate, quenching distance, jet stopper release just before quenching etc
	Motorised Water Circulation with storage & test tank.
	Hardness testing fixture for progressive hardness Indentations

Top

Precision Diamond Sectioning Machine -
Model “METACUT-DCM”

	Effective solution for cutting fragile / extreme hard / Soft materials with minimal surface deformation
	Precision job positioning by micrometer
	Diamond blade (0.015, 0.30, 0.40 mm.(High / low concenration diamond)
	Various holders for different material shapes’ sectioning
	Attachment for PCB (PTH) sectioning
	High Torque Motor – 180 watts.
	Speed Variation – Stepless up to 500 r.p.m.

Top

Muffle Furnace - Model : MTI-1200

	Chember – 6 x 6 x 12 inch. Ceramic Lined
	Max. Temp. 1200ºC, 3 KW Kanthal A1 (15swg)
	Control Panel – Digital controller, Ammeter, Contactor etc

Top

Erichson Cupping Tester - Model : META-ERICH-I

	Direct depth indication on the dial gauge
	Resolution of 0.1 mm
	Capacity : 2mm, thick sheet of ferrous & 2.8 mm thick sheet of non ferrous material

Top